Eigenen Rechner in das Freifunk-Netz: Unterschied zwischen den Versionen
Zur Navigation springen
Zur Suche springen
Rubo77 (Diskussion | Beiträge) |
Rubo77 (Diskussion | Beiträge) (→Start-Script erstellen: script verbessert) |
||
| Zeile 27: | Zeile 27: | ||
echo "stopping network-manager" | echo "stopping network-manager" | ||
| − | + | service network-manager stop | |
echo "pls wait" | echo "pls wait" | ||
sleep 10 | sleep 10 | ||
| + | echo turn wlan iface off | ||
ifconfig $IFACE down | ifconfig $IFACE down | ||
| + | echo set maximal transfer unit from standard 1500 to 1528 | ||
ifconfig $IFACE mtu 1528 | ifconfig $IFACE mtu 1528 | ||
| + | echo turn wlan encryption off | ||
iwconfig $IFACE enc off | iwconfig $IFACE enc off | ||
| + | echo start ad-hoc mode | ||
iwconfig $IFACE mode ad-hoc essid batman.kiel.freifunk.net ap 02:ca:ff:ee:ba:be channel 11 | iwconfig $IFACE mode ad-hoc essid batman.kiel.freifunk.net ap 02:ca:ff:ee:ba:be channel 11 | ||
| + | echo load module into kernel | ||
modprobe batman-adv | modprobe batman-adv | ||
| + | echo adding iface to batman | ||
batctl if add $IFACE | batctl if add $IFACE | ||
| + | echo turn wlan iface on | ||
ifconfig $IFACE up | ifconfig $IFACE up | ||
| + | echo turn batman iface on | ||
ifconfig bat0 up | ifconfig bat0 up | ||
echo "batman.kiel.freifunk.net on $IFACE should be ready" | echo "batman.kiel.freifunk.net on $IFACE should be ready" | ||
| − | echo "internet starting, this may take some minutes..." | + | echo "internet starting, this may take some minutes due to latency..." |
dhclient bat0 | dhclient bat0 | ||
echo "internet connection IP:" | echo "internet connection IP:" | ||
ifconfig|grep Bcast | ifconfig|grep Bcast | ||
| − | + | echo | |
echo "to resume normal networking just restart the networkmanager:" | echo "to resume normal networking just restart the networkmanager:" | ||
| − | echo " | + | echo "service network-manager restart" |
| + | echo "batctl if del $IFACE" | ||
| + | echo "echo it can take a few minutes until network-manager gets a new route" | ||
| + | echo | ||
</pre>''' | </pre>''' | ||
Version vom 20. November 2012, 21:47 Uhr
So einfach kann man seinen Laptop in das Freifunk-Netz als Knoten mit integrieren (Unter Ubuntu 12.04 getestet):
Installation
sudo apt-get install batctl
Kernelmodul laden:
sudo modprobe batman-adv
Version prüfen:
sudo batctl -v
Nicht alle Batmanversionen sind kompatibel - siehe: http://www.open-mesh.org/projects/batman-adv/wiki/Compatversion
Start-Script erstellen
Um sich mit batman.kiel.freifunk.net auf der Schnittstelle wlan0 mit der bssid 02:ca:ff:ee:ba:be zu verbinden erstelle folgendes script und nenne es z.B. /usr/local/sbin/freifunk-connect:
#! /bin/bash IFACE=wlan0 if [ "$(whoami &2>/dev/null)" != "root" ] && [ "$(id -un &2>/dev/null)" != "root" ] ; then echo "You must be root to run this script!"; exit 1 fi echo "stopping network-manager" service network-manager stop echo "pls wait" sleep 10 echo turn wlan iface off ifconfig $IFACE down echo set maximal transfer unit from standard 1500 to 1528 ifconfig $IFACE mtu 1528 echo turn wlan encryption off iwconfig $IFACE enc off echo start ad-hoc mode iwconfig $IFACE mode ad-hoc essid batman.kiel.freifunk.net ap 02:ca:ff:ee:ba:be channel 11 echo load module into kernel modprobe batman-adv echo adding iface to batman batctl if add $IFACE echo turn wlan iface on ifconfig $IFACE up echo turn batman iface on ifconfig bat0 up echo "batman.kiel.freifunk.net on $IFACE should be ready" echo "internet starting, this may take some minutes due to latency..." dhclient bat0 echo "internet connection IP:" ifconfig|grep Bcast echo echo "to resume normal networking just restart the networkmanager:" echo "service network-manager restart" echo "batctl if del $IFACE" echo "echo it can take a few minutes until network-manager gets a new route" echo
Wenn das script ausgeführt wird, dann ist dein Rechner Teil des Freifunk-Netzwerkes und mescht mit. Er kann so also auch als Brücke zwischen zwei Routern fungieren, die zu weit auseinander liegen.
Siehe auch: Askubuntu